THE AVIATION SUPERSTORE FOR ALL YOUR AIRCRAFT & PILOT NEEDS | +61 (1800) 953522

Bose 6 Pin Lemo Headset Install Connector Kit

$109.95/Each
Price Includes GST
Quantity
Add to Wishlist
Part# 11-01846
MFR Model# 323172-0010

Overview

Custom panel connector and attached wiring harness for use with installed headsets. Semi-permanent installation provides aircraft power and audio to headset. Three-foot wiring harness allows for placement in locations throughout aircraft.

Note: The headset install kit is FAA approved part of the A20 TSO.

Features

  • Self-latching, precision-designed, quick-connector wiring harness for panel mounting in aircraft with 10-32 volt DC systems
  • Installation wire diagram and step-by-step instructions included
  • Panel connector must be mounted by qualified avionics technician
  • Frequently Purchased With
  • Customers Also Viewed

Reviews

still pending - but looks as expected

C. L Verified Purchase

Bose Lemo 6 Pin Jack Install Kit

September 11, 2023

Victoria A Verified Purchase

Bose Lemo 6 Pin Jack Install Kit

February 28, 2023

Worked fine. Replaced an older LEMO jack. The new one uses thicker wires, which is good because the old one had very thin fragile wire. And FYI, the new jack has slightly larger OD so youll need to enlarge your mounting hole if replacing an older one like I did.

Jeff B Verified Purchase

Bose Lemo 6 Pin Jack Install Kit

November 16, 2022

good deal

Karl R Verified Purchase

Bose Lemo 6 Pin Jack Install Kit

January 28, 2022

good product

Roy B Verified Purchase

Bose Lemo 6 Pin Jack Install Kit

October 7, 2021

E. G Verified Purchase

Bose Lemo 6 Pin Jack Install Kit

June 1, 2021

The order went fine

Anthony P Verified Purchase

Bose Lemo 6 Pin Jack Install Kit

May 25, 2021

Product was delivered on time, and in excellent condition.

Henry B
March 17, 2021

excellent

Shai B
January 15, 2021

Just what we needed and the cost was the best I could find. Item as advertised and pictured.

Jonathan
August 21, 2020

Q&A

Please note, Aircraft Spruce Australia's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce Australia assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: Does this one jack/wire harness connect the headphone and microphone to the intercom? Can it be wired so my headset runs off the aircraft power instead of a battery?

This is the part you order if you want to put a LEMO panel power jack instead of installing mic/headphone jacks in the panel. You have to have a headset with the 6 pin LEMO plug for this to work without batteries in your headset.

Q: will this allow the use of the bose X as well as the new BoseA20?

This is for the installation of a 6 PIN Lemo power jack in the panel and is designed to work with any headset which is a 6 Pin Lemo Headset. The 6 PIN Lemo versions of the Bose X and A20 are supported.

Q: What diameter hole is required to mount the Bose A20 6 pin lemo connector install kit?

The connector requires a panel hole that is 12.5mm (0.49") wide, by 14.0mm (0.55") tall.

Q: How long are the harness wires? Is there a wiring diagram for this?

The wiring for the harness is three foot long. A step by step wiring diagram is included with the install connector kit.

Q: Can this me installed in addition to the GA connections or do the GA connections have to be removed? In other words what if you also wanted to keep the dual plug GA as well?

Yes, it is possible to have both jacks installed in the aircraft.

Q: If I install it to a Tango Headset, Will it charge the battery in the control unit?

No, this does not charge a Tango battery kit.

Q: Will it work with Lightspeed Zulu 3?

Yes this will work with all Lemo style headsets.

Q: What is the thread size and pitch for the nuts that hold it to the panel?

M14 x 1

Q: can this unit be soldered to the existing typical headset non-powered jacks... ? and be used either way? looking for a wire diagram

You can have both the Lemo and GA plugs but we believe the Lemo plug would need to be wired into the intercom separately. It would also need power.

Q: What is the LEMO part number of the 6-pin connector used on this cable?

You can use Bose A20 cable assembly 11-08734 or you can use an adapter to connect to the LEMO receptacle.

View in Catalog

View Image View in Catalog