Good looking product. The adhesive backing seems not very sticky. I guess time will tell have not run with product installed yet

Carl M Verified Purchase

Heat Barrier 12X24 Adhes Bck

Havent put it on yet, I have hi hopes

Kays A Verified Purchase

Heat Barrier 12X24 Adhes Bck

have used before ,works very good

Dennis L Verified Purchase

Heat Barrier 12X24 Adhes Bck

Arrived promptly. Product is easy to work with. Simply cut with scissors, then peel and stick.

Denise B Verified Purchase

Heat Barrier 12X24 Adhes Bck

A good product.

Patrick K Verified Purchase

Heat Barrier 12X24 Adhes Bck

Good and cost-effective product. Also use on race cars

Patrick R Verified Purchase

Heat Barrier 12X24 Adhes Bck

Installation was as expected. Cut with scissors to size. Rounded corner cuts. Cleaned area well. Applied. Warmed with heat gun to ensure the adhesive made a good bond. Sealed all edges to prevent future peeling with red RTV.

Bill W Verified Purchase

Heat Barrier 12X24 Adhes Bck

Great for reflecting heat inside fiberglass cowls.

Mark F Verified Purchase

Heat Barrier 12X24 Adhes Bck

Great Product

James W Verified Purchase

Heat Barrier 12X24 Adhes Bck

Great product and exactly like listed! Very durable! Thank you!

Excellent for cowling insides

Very useful

It works.

Great stuff. Easy to work with and economical. Only recently installed in lower cowl, so cant rate longevity of product in use. Will adjust rating if insulation doesnt hold up over long time usage.

Adheres well in my fiberglass cowling. Was easy to apply. Used it to protect the fiberglass from the direct heat of the cylinders. Now lets see, how well it lasts in the long run.

I ride a KTM 1290 SA with a serious problem with heat radiating off of the engine head that is just below the seat. Talking to a custom motorcycle seat builder, he suggested this product and it works great! Im much more comfortable now, which means Im less distracted and likely a safer rider. Great flexible product thats easy to cut, shape and adhere to items that arent flat. Quick delivery, but really overpacked.

Good to work with

I used this heat material to protect the inside of a RV-9 cowl. It was easy to apply and I was able to work it around some slight bends. With a few relief cuts it looks great. The material is strong with insulation under the foil. The adhesive seems to be strong.

Covered Firewall as extra heat barrier and performs well!

I have used this product on inlet system of turbo charged car and on underside of road race motorcycle fuel tank. Easy to work with & reflects radiant.

Too early to tell, but took out old cowling insulation and replaced with this heat barrier under an O-540. Hope it works

Jeff A Verified Purchase

Heat Barrier 12X24 Adhes Bck

I was looking for something to apply to the inside of my lower cowl. This product is nice and thin but the adhesive backing seems to be made more for a smooth surface so I did not use it for what I had intended.

Bob H Verified Purchase

Heat Barrier 12X24 Adhes Bck

Material was great. Shipping was less than Satisfactory.

Cost effective alternative to the more expensive options. Used it to replace old insulating material on inside of my cowling near exhaust manifold. Despite diligent cleaning efforts, if the surface you are putting this stuff on has ever seen oil, use good contact cement. The adhesive backing will not work.

The product is easy to work with, in terms of cutting and shaping it, but the adhesive on the 4 pieces I purchased was not good - adhesive was barely tacky at best.

Works good, used it for the inside of my bottom cowl, PA32. Three stars because even though I soap washed and solvent washed the surface I still needed to use additional adhesive to get it to stay attached.

Eric C Verified Purchase

Heat Barrier 12X24 Adhes Bck

Used inside of lower cowling lasted for 175 hours of flying , the adhesive letting go along the edges. Replacing new with the same product, but will use an additive adhesive.

I use this barrier to protect my fiberglass cowling from exhaust pipe heat. The adhesive is adequate to hold it in place when all residual oil is removed. This is done with a sequence of solvents. Once clean, l apply the heat shield material. Since the edges of the shielding is unprotected, from soaking up oil, I apply a high temp RTV to seal all the edges.

adhesive not very strong, had to epoxy some of the areas

Franz F Verified Purchase

Heat Barrier 12X24 Adhes Bck

Adhesive Backed? only in words. The adhesive is weak. Brand new RV-8 cowlings were cleaned up really well and this Thermo-Tec did not hold at all. Like the last review guy, I am going to have to find an adhesive for it... not cool.

The peel-n-stick adhesive provided is not sticky enough to hold the product on my fiberglass engine cowling. The bond strength is very poor even on flat area. There are no installation instruction with the product. Now I need to find another appropriate adhesive.